RF remote control using codec chip ST14

Abstract: -  Here to make a IR remote control I am using an ASIC codec chip ST12. codec means coder+decoder. That means same chip is used as encoder at transmitter side and as decoder at receiver side. Its very nice chip and some of the major features of the chip are

• Encode / Decode on single chip
• Built in Oscillator
• Minimum External Components
• Wide operating voltage range. (2.0 - 5.5V)
• Single chip Encoding Decoding Mode
• 40kHz carrier for infrared transmission medium
• 18 pin DIP package

The major applications of this chip

• Burglar alarm system
• Smoke and fire alarm system
• Garage door controllers
• Car door controllers
• Car alarm system
• Security system
• Cordless telephones
• Other remote control systems

Note: - IC is available atwww.sunrom.com. The information of this chip given here is taken from st14 datasheet also available at www.sunrom.com

                                                              _______________________________

Because both transmitter and receiver made up of only ST14 codec chip, let us first understand pin diagram, pin function and working of this chip and then go for transmitter and receiver.

Pin diagram: -

As shown in above figure its 18 pin chip with DIP. Pals refer the table given below for details

Pin no	Pin name	Description	Function
1 to 4	A0 - A3	address inputs	to setup an address for the system. each pin can either be connected to 0V or Vcc. can not be left unconnected
5	gnd	0v input	connected to circuit ground
6 to 13	row-col outx	row-column input or output	at transmitter side in encoder mode works as input (8 switches are connected in 4x2 matrix on 4 rows and 2 columns) and at receiver side in decoder mode works as output (connected to external circuit)
14	Vcc	+V input	connected with +V of 2 to 5 V
15	mode Rx - Tx	receiver or trasmitter	high or low logic on this pin decides its operation as transmitter or receiver. if connected to Vcc works as receiver and if connected with Gnd works as transmitter
18	Data I/O	data input or output	in encoder mode it sends data and in decoder mode receives data
17	Lat - Mom	latching or momentary	in decoder mode the output will be either latching or just momentary. if connected with Vcc output will toggle every time and if tied to ground a low-high-low pulse on pins
16	IR - RF	infra red or radio freq	selects transmission via either IR or RF. if tied to Vcc transmits 40 KHz signals via IR led and if tied to Gnd sends data via suitable RF transmitter

So now after going through above table one should have complete idea about the operation of this chip as transmitter (encoder) and as receiver (decoder).

Transmitter: - as written above the major advantage of this chip is that there is least requirement of external components

As shown in above figure along with ST14 we require 8 push button switches, one LED with current limiting register and an ASK transmitter

Connection: - All four address bits A0 - A3 are shorted to ground to setup an address 0000. 8 push button type switches are connected in row-column (4x2) structure as shown. The transmit data pin drives red LED with 330E resistor and also connected with data i/p of 433 MHz ASK Tx. IR-RF pin is connected to Gnd to configure the chip in RF mode. Mode Rx-Tx pin is also connected with Gnd to configure it as transmitter. A 3V battery (or 2 dry cell) provides power to the circuit.

Operation: - When any of the key is pressed data is transmitted via transmit data pin. The address and data together given to ASK transmitter that will modulate it at 433 MHz freq. This data transmission can be seen on red LED as blinking o/p.

Receiver: -

Connections: - All four address bits A0-A3 are connected to ground to setup same address 0000. Keeping first data o/p D0 unconnected, rest all D1 - D7 are connected to input of ULN chip. Each one output of ULN chip drives one relay and one LED. So total there are seven relays that can switch on / off 7 different devices (instead of ULN2003 if one uses ULN2803 then all 8 data outputs can be used). The mode Rx-Tx pin is connected to Vcc to configure the chip as receiver. The lat-mom pin is tied to Vcc to get toggle output every time. The output of 433 MHz ASK Rx is connected to receive data pin of ST14. Two different regulated supplies 5V and 12 V are used to give power to complete circuit. 

Operation: - The 433 MHz ASK Rx will detect the carrier signal and demodulate the address and data and give it to ST14. On getting valid address and data st14 will latch the data on D0-D7. Because its toggle output every time when same switch is pressed from TX, the relay will switch on / off. Also relay on / off is indicated by respective LED.